HVAC Services Oakley, CA

I repaired a Carrier AC system in Oakley today. The system wasn’t cooling properly due to a clogged evaporator coil. After cleaning the coil and checking the refrigerant levels, I tested the system. The AC is now running efficiently and cooling the space as expected.

Today, I performed a filter change-out on a Lennox HVAC system in Oakley. The existing filter was clogged, reducing airflow. I replaced it with a new MERV 11 filter to improve air quality and system efficiency. The HVAC system is now running at optimal performance.

Perform regular pm on furnace in attic , change and date filters , check over all heating components for proper operation , check gas valve , check pressure switch , check inducer , check combustion analysis , noticed water stains on flue pipe , I’ll make a note so the next technician knows to check on it ,check and clean flame sensor , verified normal operation

Perform regular on on furnace in attic , change and date filter , explained about future filters , checked over all heating components for proper operation , check gas valve , check pressure switch , check inducer , check combustion analysis, check capacitors , check and clean flame sensor, check thermostat function , verify normal operation

Perform regular pm on furnace in garage , changed that supplied air filter and dated , check over all heating components for proper operation , check gas valve , check pressure switches , check inducer , check combustion analysis , check thermostat heating function , verify normal operation

Perform regular pm on furnace in attic , check over all heating components for proper operation , check gas valve , check pressure switch , check and clean flame sensor , check capacitor , check thermostat heating function , check combustion analysis verify normal operation

In Oakley, CA, I replaced an old thermostat with a new, programmable model to improve system control and efficiency. I also diagnosed a faulty pressure switch on the furnace, which required replacement, and signed the customer up for a comprehensive maintenance plan to ensure regular system upkeep.

Installed a ductless heating system in Oakley, CA. The customer chose a Daikin ductless unit for their home office. I mounted the indoor air handler and connected it to the outdoor compressor. After running refrigerant lines and electrical, I verified the system’s operation, ensuring efficient heating performance.

Performed a full HVAC repair in Oakley, CA, today. The blower motor had failed on a Lennox EL296V furnace. I replaced the motor and cleaned out dust buildup in the unit. After reassembling the system, I tested the airflow and ensured proper heating performance.

I performed HVAC fall maintenance in Oakley, CA, on a Trane XV80 system. I checked the thermostat, inspected the air filters, and cleaned the condenser coils. After ensuring the system was running efficiently, I tested the airflow to confirm proper heating throughout the home.

I installed an air purifier integrated into an HVAC system to improve indoor air quality. After mounting the UV-C air purifier inside the ductwork, I connected it to the HVAC power supply. I tested the system, ensuring it was filtering out airborne particles such as dust and allergens. The air quality in the home has significantly improved.

I sealed air ducts in a home where the homeowner was experiencing uneven temperatures. After inspecting the ductwork, I found multiple leaks around the joints. I used mastic sealant and aluminum tape to seal the leaks, ensuring improved airflow and energy efficiency. The system is now distributing air evenly throughout the home.

I completed fall furnace maintenance by inspecting the heat exchanger for cracks and cleaning the burner assembly to improve combustion. I replaced the air filter and tested the flame sensor for proper operation. Additionally, I lubricated the blower motor and checked the thermostat to ensure the system is ready for the colder months ahead.

I performed an AC repair by diagnosing a faulty capacitor, which was preventing the compressor from starting. After replacing the capacitor, I checked the refrigerant levels and found them within the proper range. I then tested the blower motor and thermostat to ensure the system was functioning correctly. The air conditioning system is now cooling efficiently.

Performed comprehensive air duct cleaning on a two-story home. Used HEPA-filtered negative air machine to create system-wide vacuum. Agitated ducts with pneumatic tools and brushes. Cleaned supply registers, return grilles, and plenums. Applied EPA-registered antimicrobial treatment. Improved system airflow and reduced particulate matter in home.

Replaced a Lennox 12 SEER split system with an American Pride 16 SEER model for improved cooling. Sized new system based on Manual J load calculation. Mounted new American Pride outdoor unit on vibration pads, installed copper line set with nitrogen purge during brazing. Set up matching air handler with ECM blower motor. Evacuated system to 500 microns, charged with R-410A. Tested all modes for proper operation.

Repaired an air conditioning system on a Day & Night unit. Diagnosed the issue as a faulty capacitor that was preventing the compressor from starting. Replaced the capacitor with a 45/5 MFD 440V model and inspected the condenser fan motor to ensure it was operating correctly. Checked refrigerant levels and system pressures, confirming they were within the proper range. Tested the system to verify it was cooling effectively. The unit is now running efficiently and providing proper cooling.

Executed replacement of dual run capacitor on Carrier 24ABC6 central air conditioning unit. Diagnosed 45/5 μF capacitor failure using Fluke 902 FC HVAC clamp meter. Safely discharged existing capacitor before removal. Installed new OEM-equivalent GE Genteq C4455R capacitor, ensuring proper microfarad rating and voltage match. Verified secure fastening and correct wiring to compressor and fan terminals. Conducted amperage draw test on both motors, confirming improved performance. Checked system pressures and subcooling to ensure optimal operation. Unit now functioning at peak efficiency with restored cooling capacity.

Repaired an AC system with wiring damage caused by rodents. Replaced all compromised wires with new, high-quality insulated conductors. Inspected the entire electrical system for additional damage and ensured proper connections. Tested the unit to verify safe and efficient operation. Proper wiring maintenance is crucial for preventing electrical hazards and ensuring reliable AC performance.

Implemented advanced air purification system: whole-house UV air cleaner installation. Integrated UV-C germicidal lamp (254 nm wavelength) into existing HVAC ductwork. Installed 24V transformer for power supply. Mounted lamp perpendicular to airflow for maximum microbial exposure. Ensured proper safety interlocks and indicator lights. System designed to neutralize airborne pathogens, including bacteria, viruses, and mold spores. Improves indoor air quality by reducing biological contaminants throughout the home.

Completed AC repair on a Carrier Infinity 24 unit. Addressed a clogged condensate line causing water backup. Turned off the system and removed the blockage using a wet/dry vacuum. Flushed the line with a bleach solution to prevent future clogs. Reconnected the line and tested for proper drainage. Checked the evaporator coil for cleanliness and ensured the drain pan was secure. Verified the system's operation to ensure effective cooling and efficient condensate removal.

Performed AC repair on a Lennox XC21 unit. Diagnosed the issue as a malfunctioning condenser fan motor. Shut off power to the unit and removed the faulty motor. Installed a new OEM condenser fan motor, ensuring proper alignment and secure mounting. Reconnected the wiring and restored power. Verified correct rotation and airflow direction. Checked refrigerant levels and system pressures to ensure optimal performance. Tested the unit to confirm efficient cooling operation and reliable condenser function.

Completed a spring AC check-up on a Trane XR16 unit. Inspected the air filter and replaced it for optimal airflow. Checked refrigerant levels and ensured they were within manufacturer specifications. Cleaned the evaporator and condenser coils to improve efficiency. Tightened electrical connections and tested the capacitor and contactor for proper function. Verified thermostat accuracy and system pressures. Ensured the unit is ready for reliable and efficient cooling throughout the summer.

I did an conditioning repair job for a customer in Caputo Cir Oakley. The customer was facing issues with their air conditioner, and I quickly identified the problem and provided a solution. I replaced the faulty thermostat and ensured the system was running efficiently. The customer was pleased with the quality of my work and the efficiency of my service.

I recently completed a seasonal heating and cooling check-up for a client. As an HVAC contractor, my responsibilities included inspecting and maintaining the heating and cooling systems in the client's home. I checked the condition of the equipment, such as the furnace, air conditioner, and thermostat, and made any necessary repairs or adjustments. I also checked and cleaned the air filters, ensuring optimal air quality and efficiency. Finally, I tested the entire system to ensure it was operating correctly and safely.