AC and Heating Service and Installation Brentwood, CA

Responded to a no-heat call in Brentwood today. The homeowner's gas furnace was not igniting. Upon inspection, I found that the flame sensor was malfunctioning. The flame sensor is a critical safety device in Brentwood that ensures the gas burner shuts off if the flame goes out, preventing a dangerous buildup of gas. In this case, the sensor was not detecting the flame properly, causing the furnace to shut down. I carefully cleaned the flame sensor to remove any soot or debris that might be interfering with its operation. After cleaning, I tested the sensor and confirmed it was functioning correctly. The furnace is now operating safely and reliably, providing heat to the home. Remember, a malfunctioning flame sensor can be a serious safety concern, so regular furnace maintenance is crucial.

In Brentwood, I diagnosed a gas furnace with a no-heat issue. The problem was a faulty igniter. I replaced the old igniter with a new one, ensuring proper placement and connection. Then, I tested the furnace to confirm the new igniter was properly igniting the gas and establishing a stable flame. The furnace is now back up and running, providing reliable heat for the homeowner.

Perform regular pm on furnace in attic , check over all heating components for proper operation and tolerances , verified normal operation

Perform regular pm on furnace in attic , check over all heating components for proper operation and tolerances , verified normal perdition

Perform regular pm on furnace in attic , check over all heating components for proper operation , check gas valve , check pressure switch , check and clean flame sensor , check inducer and blower amps , found bad blower capacitor (recommend replacement) , replaced capacitor for blower motor , change and date filter , cycled heat , verify normal operation at time of service

Perform regular pm on furnace in attic , check over all heating components for proper operation , check gas valve , check pressure switch , check and clean flame sensor , check inducer and blower amps , found bad blower capacitor (recommend replacement) , replaced capacitor for blower motor , change and date filter , cycled heat , verify normal operation at time of service

Fixed issue with furnace recommended a zone board in the future

Found blown out high voltage wires supplying furnace , replaced wiring checked over amperage and cycled unit , verified normal operation

I repaired a York heat pump in Brentwood that wasn’t heating. The issue was a malfunctioning defrost board. I replaced the board, cleaned the air handler, and checked the system’s refrigerant levels. The heat pump is now working efficiently and providing consistent heat.

I completed heater repair on a Honeywell system in Brentwood. The thermostat was not controlling the temperature properly. After recalibrating the thermostat and checking the wiring connections, the system began operating as expected, delivering consistent heat.

Perform regular pm on furnace in garage , check over all heating component for proper operation , check gas valve , check pressure switch , check inducer , check capacitor , check and clean flame sensor , check combustion analysis , change and date filter , told customer about filters for future , verified normal operation

Performed regular pm on furnace in attic , checked over all heating components for proper operation , checked gas valve , checked capacitor , check pressure switches , checked thermostat heating function and verified normal operation

No heat call - found dirty flame sensor and faulty signal from thermostat , cleaned off flame sensor and changed out thermostat , verified normal operation

Perform regular pm on furnace in closet , change and date filter , check over all heating components for proper operation , check gas valve , check pressure switch , check and clean flame sensor , check thermostat heating function , check combustion analysis , verify normal operation

Working in Brentwood, CA this afternoon. Performed regular preventative maintenance on both furnaces in the attic , found bad capacitors and replaced at this visit , checked over all heating components for proper operation and verified normal function

In Brentwood, Ca this morning I performed regular pm on furnace in attic , check over all heating components for proper operation , check gas valve , check pressure switch , check inducer , check and clean flame sensor , check combustion analysis , check thermostat , needs to filter asap and filter grill cleaned , verified normal operation at time of visit , cycled heat , no adjustments or repairs needed at this time.

I completed routine maintenance on a Trane S9X1 gas furnace in Brentwood, CA. I started by inspecting the burners and cleaning the heat exchanger to remove soot buildup. I replaced the old 16x20x1 air filter and lubricated the blower motor bearings. The gas valve was tested and calibrated for proper operation. I also cleaned the flame sensor and ensured the thermostat was functioning correctly. After thorough testing, the furnace was running smoothly and ready for winter.

In Brentwood, CA, I cleaned the air ducts using a Rotobrush BrushBeast machine. The ducts were thoroughly vacuumed, removing debris and allergens. Afterward, I sealed all duct joints with aluminum tape, improving airflow and enhancing the home’s air quality.

I installed a new American Pride Series gas heater in Brentwood, CA, replacing an outdated unit. The project included setting up the supply and return air ducts, connecting the gas line, and installing a high-efficiency thermostat. I tested the system to ensure proper ignition and airflow. The new heater included advanced safety features and an upgraded heat exchanger, providing enhanced energy efficiency. After installation, I conducted multiple heating cycles and calibrated the system for optimal performance. The homeowner now has a reliable heating system ready for the colder months.

I completed a full air duct cleaning for a home in Brentwood, CA using a Rotobrush BrushBeast system. I removed dust, allergens, and debris from the ductwork and sanitized the system with an antimicrobial spray. Post-cleaning airflow tests confirmed improved system efficiency and better indoor air quality for the client.

I conducted a furnace maintenance check on an American Standard Silver 95 gas furnace in Brentwood, CA. Tasks included inspecting the burners, lubricating the blower motor, and replacing a clogged 20x25x1 air filter. I also checked the thermostat for accurate readings and tested the safety controls. The furnace was left operating efficiently and safely.

I completed an HVAC heating maintenance service in Brentwood, CA. I inspected the flame sensor and cleaned the burner assembly. I also replaced the furnace filter and checked the thermostat for accuracy. The system is ready for the upcoming colder months, providing efficient and safe heating.

I installed a new American Pride Series HVAC system in Brentwood, CA. The unit was a 15 SEER heat pump with a variable-speed air handler. After setting up the outdoor condenser and connecting the refrigerant lines, I tested the system’s heating and cooling functions to ensure everything was working smoothly.

I installed a new American Pride 3-ton HVAC system for a homeowner. After removing the old unit, I connected the new condenser and air handler to the existing ductwork. I calibrated the thermostat and tested the system for proper airflow and cooling. The American Pride system is now providing efficient cooling throughout the home.

I completed an HVAC cooling repair by inspecting the evaporator coil, which was clogged with debris. After cleaning the coil, I found low refrigerant levels and recharged the system with R-410A refrigerant. I tested the blower motor and ensured the compressor was functioning properly. The system is now running smoothly and cooling the home effectively.